Allen Bradley Modules 1756-IB16 1756 IB16 AB 1756IB16 A DC Input Module Highest

Product Specification

Allen Bradley Modules 1756-IB16 1756 IB16 AB 1756IB16 A DC Input Module Highest version

Product Description:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

Related Product Recommendation:

Product's Character:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

1747-UIC USB to DH-485 Interface Converter AB
1747OC-EDEBA Open Controller - CPU Module AB
1756-A13/A 13 Slot Chassis - Series A AB
1756-A13/B 13 Slot Chassis - Series B AB
1756-A17/A 17 Slot Chassis - Series A AB
1756-A17/B 17 Slot Chassis - Series B AB
1756-BA2 Battery Assembly AB
1756-CNB/D ControlNet Bridge Module - Series D AB
1756-CNB/E ControlNet Bridge Module - Series E AB
1756-DHRIO/B DH+/RIO Bridge/Scanner Module - Series B AB
1756-DHRIO/C DH+/RIO Bridge/Scanner Module - Series C AB
1756-DHRIO/D DH+/RIO Bridge/Scanner Module - Series D AB
1756-DHRIO/E DH+/RIO Bridge/Scanner Module - Series E AB
1756-DNB/A DeviceNet Bridge/Scanner Module - Series A AB
1756-DNB/B DeviceNet Bridge/Scanner Module - Series B AB
1756-DNB/D DeviceNet Bridge/Scanner Module - Series D AB
1756-DNB/E DeviceNet Bridge/Scanner Module - Series E AB
1756-IB16/A Digital Input Module AB
1756-IB16D/A Digital Input Module AB
1756-L1/A Logix5550 Processor AB

1756-L1M1/A Logix5550 Processor AB
1756-L1M2/A Logix5550 Processor AB
1756-L1M3/A Logix5550 Logix5550 Processor AB
1756-L55M12/A 1756-L55/A, 1756-M12/A Logix5555 Processor, 750KB memory, Series A AB
1756-L55M13/A 1756-L55/A, 1756-M13/A Logix5555 Processor, 1.5 MB memory, Series A AB
1756-L55M14/A 1756-L55/A, 1756-M14/A Logix5555 Processor, 3.5 MB memory, Series A AB
1756-L55M16/A 1756-L55/A, 1756-M14/A Logix5555 Processor, 7.5 MB memory,

The use of the product: