RJLD-043TC1 Magnetic RJ45 Jack wiki 10/100 BASE FILTER WITH CONNECTOR

Product Specification

RJLD-043TC1 Magnetic RJ45 Jack wiki 10/100 BASE FILTER WITH CONNECTOR

Designing Model: 【RJLD-043TC1】    Mass Production Model:【LPJ4126ABNL】

LAN 10/ 100BASE T RJ45 Jack With Magnetic module

◎ RoHS Compliant 
◎ Fully shielded magnetics protect data from internally generated digital noise 
◎ Reduces the overall length of the signal path for improved common mode performance 
◎ Implements full common mode termination scheme with used and unused twisted pairs 
◎ Meets IEEE802.3 Baseline Wander Compensation specification 
◎ Integrates high voltage capacitor to chassis ground 
◎ Supports all major transceivers with matched turns ration and complete integration of 
specified termination 
◎ Design for 100base-tx transmission over UTP-5 cable 
◎ Operating TEMP. range : -40℃ to +85℃ 
◎ Storage TEMP. range : -55℃ to +125℃ 
◎ Primary OCL inductance : 350µH MIN. at 100KHz/100mV with 8mA DC bias 
◎ With the LED lamp

MAG.REVERSE LATCH ,

LED optional ; EMI-finger Optional.

Description

RJLD-043TC1 Magnetic RJ45 Jack wiki 10/100 BASE FILTER WITH CONNECTOR

1. Product Type Features:                                                  

  1) Product Type = Connector  
  2) Jack Type = RJ45 
  3) Profile = Standard 
  4) PCB Mounting Orientation = Side Entry (Right Angle)/Top Entry(Vertical)

2. Mechanical Attachment: 
  1) Jack Configuration = 1 x 1

3. Electrical Characteristics: 
  1) Shielded = Yes

4. Termination Related Features:
  1) EMI Finger - Bottom = Without
  2) Termination Method = Solder

5. Body Related Features:
  1) Port Configuration = Single/Multi
  2) EMI Fingers -Top and Sides = With/ Without
  3) Latch Orientation = Standard - Latch Down
  4) PCB Tail Length

6. Contact Related Features:
  1) Preloaded = Yes
  2) Contact Termination Type = Through Hole/Surface Mount

7. Housing Related Features:
  1) Connector Style = Jack

8. Industry Standards:
  1) RoHS/ELV Compliance = RoHS compliant, ELV compliant 
  2) Lead Free Solder Processes = Wave solder capable to 240°C,

      Wave solder capable to 260°C, Wave solder capable to 265°C

      Reflow-Soldering Optional;
  3) RoHS/ELV Compliance History = Always was RoHS compliant

9. Identification Marking:
  1) Left LED Color (Position #1) = Green - 250 ohm resistor
  2) Right LED Color (Position #2) = Green - 250 ohm resistor

10. Conditions for Usage:
  1) Applies To = Printed Circuit Board
  2) Environmental Conditions = Office / Premises
  3) Operating Temperature (°C ) = 0 - 70/-40 - +85

11.Hipot:

     1500Vrms MIN

Applications For Terminal User

Designed to support applications, such as ADSL modems, LAN-on-Motherboard. Networking and communication equipments such as HUB, PC card, Switch, Router, PC Mainboard, SDH, PDH, IP Phone, xDSL modem,Call Center solutions , Complex set top boxes , VOIP gateways setup,Border Gateway Protocol,fast ethernet switch ...

Competitive Advantage

RJLD-043TC1

18 years production experience,

2600 staff,

100% test

Flexible delivery time

Main Customer

Design for Ti , Intel , Samsung ,  Fluke , Jabil  , Flextronics ,Cypress, Freescale,EKF.......

EMS Application

Built-in Flexible PCB Assembly; Rigid-Flexible PCB Assembly; Microelectronic, Flip Chip; Microelectronic, Chip On Board; Optoelectronic Assembly; RF / Wireless Assembly; Through Hole Assembly; Surface Mount Assembly; System Assembly; Printed Circuit Board Assembly

Other Replaceable List