YUHONG HOLDING GROUP CO., LTD
| Payment Terms | L/C AT SIGHT, T/T |
| Supply Ability | 500 SETS PER YEAR |
| Delivery Time | 90 - 180 days |
| Packaging Details | EXPORT STANDARD |
| Design Code | ASME VIII + IBC 2018 + ASCE 7 + NACE MR103 |
| DESIGN PRESSURE (INT / EXT) | 3.5 / F.V. (bar g) |
| DESIGN TEMPERATURE | 100℃ |
| OPERATING PRESSURE | 0.55 (bar g) |
| OPERATING TEMPERATURE | 65℃ |
| M.D.M.T. | -6℃ |
| DESIGN CODE FOR SEISMIC | IBC 2018 |
| DESIGN CODE FOR WIND | ASCE/SEI 7-22 |
| FLUID STATE (LIQUID/ GAS) | LIQUID / GAS |
| Installation | pre assembly in workshop |
| Approval | U stamp |
| Brand Name | YUHONG |
| Model Number | Amine Reflux Vessel |
| Certification | ASME U STAMP |
| Place of Origin | China |
View Detail Information
Explore similar products
Low Temperature Separator Stainless Steel / Carbon Steel Pressure Vessel ASME
Glycol Flash Vessel ASME Pressure Vessel Stainless Steel SA240 SS304 Cladding
Vertical Pressure Vessel For Stripping Column Used In Distillation And
Industrial Pressure Vessel For Regeneration Column Glycol HC Gas CO2 Fluid NACE
Product Specification
| Payment Terms | L/C AT SIGHT, T/T | Supply Ability | 500 SETS PER YEAR |
| Delivery Time | 90 - 180 days | Packaging Details | EXPORT STANDARD |
| Design Code | ASME VIII + IBC 2018 + ASCE 7 + NACE MR103 | DESIGN PRESSURE (INT / EXT) | 3.5 / F.V. (bar g) |
| DESIGN TEMPERATURE | 100℃ | OPERATING PRESSURE | 0.55 (bar g) |
| OPERATING TEMPERATURE | 65℃ | M.D.M.T. | -6℃ |
| DESIGN CODE FOR SEISMIC | IBC 2018 | DESIGN CODE FOR WIND | ASCE/SEI 7-22 |
| FLUID STATE (LIQUID/ GAS) | LIQUID / GAS | Installation | pre assembly in workshop |
| Approval | U stamp | Brand Name | YUHONG |
| Model Number | Amine Reflux Vessel | Certification | ASME U STAMP |
| Place of Origin | China | ||
| High Light | Amine Reflux Pressure Vessels ，NACE MR103 SS Pressure Vessels ，SS Pressure Vessels Anti Corrosive | ||
Pressure Vessels for Amine Reflux Vessels: Design & Considerations
Amine reflux vessels are pressure vessels designed to handle condensed liquids (water + amine) and residual acid gases (H₂S, CO₂) from the overhead of an amine stripper column. Their design follows strict standards due to corrosive conditions and operational demands.
1. Design Codes & Standards
I.> ASME BPVC (Boiler & Pressure Vessel Code), Section VIII, Div. 1 or 2 – Mandatory for pressure containment.
II.> API 12GDU (Gas Dehydration Units) – Guidelines for amine system components.
III.> NACE MR0175/ISO 15156 – Material selection for H₂S service (sour environments).
IV.> GPSA Engineering Data Book – Industry best practices for gas processing.
| Parameter | Typical Range | Notes |
| Design Pressure | 50–150 psig (3.5–10 barg) | Must exceed stripper overhead pressure. |
| Design Temperature | 200–250°F (93–121°C) | Matches stripper condenser outlet. |
| Material | Carbon steel (SS for high corrosion) | Lined or coated if severe H₂S/CO₂. |
| Corrosion Allowance | 1/8" to 1/4" (3–6 mm) | Extra thickness for amine service. |
| Vent Size | 2–6 inches (DN50–DN150) | For non-condensable gas release. |
3. Material Selection
I.> Carbon Steel (SA-516 Gr. 70) – Most common, cost-effective, but requires amine-compatible coatings/inhibitors.
II.> Stainless Steel (SS 304/316) – Used for high H₂S/CO₂ or oxygen-contaminated systems.
III.> Clad Materials (CS + SS overlay) – For severe corrosion zones.
IV.> Internal Linings (Fiberglass, PTFE, Epoxy) – Additional protection against wet acid gas attack.
Note: Amine degradation products (e.g., heat-stable salts) can accelerate corrosion—material choice depends on amine type (MDEA, DEA, MEA).
4. Nozzle & Internals Requirements
| Nozzle | Purpose | Typical Size |
| Inlet | From condenser | 6–12 inches (DN150–DN300) |
| Liquid Outlet | Reflux to stripper | 3–6 inches (DN80–150) |
| Vent | Non-condensable purge | 2–4 inches (DN50–100) |
| Drain | Sludge removal | 2 inches (DN50) |
PSV (Pressure Safety Valve) – Sized per API 520/521 for overpressure scenarios.
Rupture Disk (Optional) – For additional protection against sudden pressure spikes.
Flare/Scrubber Vent – Disposes H₂S/CO₂ safely.
| Issue | Cause | Solution |
| Corrosion | Wet H₂S, heat-stable salts | Use corrosion-resistant materials, monitor amine quality. |
| Foaming | Contaminated amine | Install mist eliminator, add antifoam agents. |
| Level Control Failure | Faulty instrumentation | Redundant level switches (LT, LAL, LAH). |
| Plugging | Degradation products | Regular flushing, filtration. |
NDT (UT, RT, PT) – Checks for wall thinning/cracks.
Thickness Monitoring – Ultrasonic testing (UT) for corrosion tracking.
Biannual Shutdown Checks – Demister integrity, nozzle condition.
Support and Services:
Our company offers comprehensive technical support and services for our Pressure Vessel product. Our team of experts is available to assist you with installation, maintenance, troubleshooting, and any other technical inquiries you may have. We are committed to ensuring that your Pressure Vessel operates efficiently and safely at all times
Company Details
Business Type:
Manufacturer,Exporter,Trading Company,Seller
Year Established:
1990
Total Annual:
50M-75M
Employee Number:
50~850
Ecer Certification：
Verified Supplier
Yuhong Holding Group equipments production base at Jiangsu Jiangyin City, Jinjiang City and Yancheng City. Total production area around 184000 square meters, main products : Heat Exchanger, Condenser, Pressure Vessel , Fired Heater, Economizer, Columns, Reactor. ... Yuhong Holding Group equipments production base at Jiangsu Jiangyin City, Jinjiang City and Yancheng City. Total production area around 184000 square meters, main products : Heat Exchanger, Condenser, Pressure Vessel , Fired Heater, Economizer, Columns, Reactor. ...
Get in touch with us
Leave a Message, we will call you back quickly!